https://wiki.frotmail.nl/index.php?action=history&feed=atom&title=Projecten%3A_3D_Printer 2026-09-26T00:51:15Z Revision history for this page on the wiki MediaWiki 1.46.0 https://wiki.frotmail.nl/index.php?title=Projecten:_3D_Printer&diff=10&oldid=prev 2022-04-04T19:04:23Z

<p>Created page with &quot;=Printer limits= Max acceleration x en y staan nu op 700 =PLA op PEI= BED op 70° =Slicer settings= {| border=&quot;1&quot; | | Print || 30 |- | Travel || 300 |- | First Layer || 15 |- | Outer perimeter || 30 |- | Inner Perimeter || 40 |- | Infill || 30 |- | Skin infill || 30 |- | Layer height || 0.2 |- | Shell Thickness || 0.96mm |- | Top/Bottom Thickness || 0.6mm |- | Flow || 97% |- | HotEnd Temp || 250 |- | Bed Temp || 88 |- | Retraction speed || 30 |- | Retraction distan...&quot;</p> <p><b>New page</b></p><div>=Printer limits=<br /> Max acceleration x en y staan nu op 700<br /> <br /> =PLA op PEI=<br /> BED op 70°<br /> <br /> <br /> <br /> <br /> =Slicer settings=<br /> {| border=&quot;1&quot; |<br /> | Print || 30<br /> |-<br /> | Travel || 300<br /> |-<br /> | First Layer || 15<br /> |-<br /> | Outer perimeter || 30<br /> |- <br /> | Inner Perimeter || 40<br /> |-<br /> | Infill || 30<br /> |-<br /> | Skin infill || 30<br /> |-<br /> | Layer height || 0.2<br /> |-<br /> | Shell Thickness || 0.96mm<br /> |-<br /> | Top/Bottom Thickness || 0.6mm<br /> |-<br /> | Flow || 97%<br /> |-<br /> | HotEnd Temp || 250<br /> |-<br /> | Bed Temp || 88<br /> |-<br /> | Retraction speed || 30<br /> |-<br /> | Retraction distance || 5<br /> |}<br /> <br /> <br /> <br /> ==Print.ini==<br /> [print]<br /> name = PETG-Print<br /> defaultQuality = diAh6hcpj6p2hS9p0UEIUdFVyz2uXTgP<br /> travelSpeedMin = 300<br /> travelSpeedMax = 300<br /> firstLayerSpeedMin = 15<br /> firstLayerSpeedMax = 15<br /> infillSpeedMin = 30<br /> infillSpeedMax = 70<br /> skinSpeedMin = 30 <br /> skinSpeedMax = 60 <br /> infillType = 0 <br /> innerPerimeterMin = 40 <br /> innerPerimeterMax = 50 <br /> outerPerimeterMin = 30 <br /> outerPerimeterMax = 50 <br /> printSpeedMin = 30 <br /> printSpeedMax = 50 <br /> nozzleDiameter = 0 <br /> gcodeFlavour = 0 <br /> retractionCombing = False <br /> combing = 2 <br /> multiVolumeOverlap = 0 <br /> cutOffObjectBottom = 0 <br /> shellThickness = 0.96 <br /> infillTopBottomThickness = 0.6 <br /> infillDensityPercent = 20 <br /> supportType = 0 <br /> platformAdhesion = 0 <br /> dualExtrusion = 0 <br /> wipeAndPrimeTower = True <br /> oozeShield = False <br /> enableRetraction = True <br /> retractionSpeed = 30 <br /> retractionDistance = 5 <br /> multiExtruderSwitchAmount = 16 <br /> startGCode = &quot;&quot;&quot; <br /> ; Default start code <br /> G28 ; Home extruder <br /> G1 Z15 F{Z_TRAVEL_SPEED} <br /> M107 ; Turn off fan <br /> G90 ; Absolute positioning <br /> M82 ; Extruder in absolute mode <br /> {IF_BED}M190 S{BED} <br /> ; Activate all used extruder <br /> {IF_EXT0}M104 T0 S{TEMP0} <br /> G92 E0 ; Reset extruder position <br /> ; Wait for all used extruders to reach temperature <br /> {IF_EXT0}M109 T0 S{TEMP0}<br /> &quot;&quot;&quot;<br /> endGCode = &quot;&quot;&quot;<br /> ; Default end code<br /> ;G1 X0 Y0 Z130 ; Get extruder out of way. Uncomment to use!<br /> M107 ; Turn off fan<br /> ; Disable all extruder<br /> G91 ; Relative positioning<br /> {IF_EXT0}T0<br /> {IF_EXT0}G1 E-1 ; Reduce filament pressure<br /> M104 T0 S0<br /> G90 ; Absolute positioning<br /> G92 E0 ; Reset extruder position<br /> M140 S0 ; Disable heated bed<br /> M84 ; Turn steppers off<br /> &quot;&quot;&quot;<br /> preSwitchExtruderCode = <br /> postSwitchExtruderCode = <br /> wipeAndPrimeTowerVolume = 15<br /> retractionMinimumTravel = 1.5<br /> minimumExtrusionBeforeRetract = 0.02<br /> zhop = 0<br /> skirtLineCount = 4<br /> skirtDistance = 6<br /> skirtMinimumLength = 150<br /> solidInfillTop = True<br /> solidInfillBottom = True<br /> infillOverlapPercent = 0<br /> supportStructureType = 0<br /> supportOverhang = 60<br /> supportFillPercent = 20<br /> supportDistanceXY = 0.7<br /> supportDistanceZ = 0.15<br /> supportExtruder = -1<br /> spiralizeOuterContour = False<br /> brimWidth = 10<br /> raftExtraMargin = 5<br /> raftLineSpacing = 1<br /> raftBaseThickness = 0.3<br /> raftBaseWidth = 0.7<br /> raftInterfaceThickness = 0.2<br /> raftInterfaceLineWidth = 0.2<br /> raftAirGap = 0<br /> raftAirGapLayer0 = 0<br /> raftSurfaceLayer = 1<br /> fixCombineEverythingA = True<br /> fixCombineEverythingB = False<br /> fixKeepOpenFaces = False<br /> fixExtensiveStitching = False<br /> fanFullAtHeight = 0.5<br /> perimeterBeforeInfill = True<br /> minimumSpeed = 10<br /> coolHeadLift = False<br /> numQuality = 1<br /> [quality_0]<br /> name = 0.2 mm<br /> signature = diAh6hcpj6p2hS9p0UEIUdFVyz2uXTgP<br /> layerHeight = 0.2<br /> layer0widthPercent = 100<br /> firstLayerHeight = 0.19<br /> <br /> ==Filament.ini==<br /> [filament]<br /> name = PETG<br /> diameter = 1.75<br /> multiplierPercent = 97<br /> printingTemperature = 250<br /> enableCooling = True<br /> bedTemperature = 88<br /> fanSpeedMin = 50<br /> fanSpeedMax = 100<br /> minimalLayerTime = 5</div>

Eric