View source for PBR

 switch1#sh ip route
 Gateway of last resort is not set
      192.168.99.0/24 is variably subnetted, 2 subnets, 2 masks
 S       192.168.99.8/29 [1/0] via 192.168.99.2
 C       192.168.99.0/30 is directly connected, GigabitEthernet1/0/28
 C    192.168.32.0/24 is directly connected, GigabitEthernet1/0/1

 switch1#sh ip int brief
 Interface              IP-Address      OK? Method Status                Protocol
 GigabitEthernet1/0/1   192.168.32.3    YES manual up                    up      
 GigabitEthernet1/0/28  192.168.99.1    YES manual up                    up     

 switch1#sh run int gi1/0/1
 interface GigabitEthernet1/0/1
  no switchport
  ip address 192.168.32.3 255.255.255.0
  spanning-tree portfast
 end

 switch1#sh run int gi1/0/28
 interface GigabitEthernet1/0/28
  no switchport
  ip address 192.168.99.1 255.255.255.252
  ip policy route-map test
 end

 switch1#sh run
 ip access-list standard loop0
  permit 192.168.99.10 log
  permit 192.168.99.12
 !
 route-map test permit 10
  match ip address loop0
  set ip next-hop 192.168.32.1		! default gateway van het 192.168.32.0/24 segment
 !
 route-map test permit 20
  set ip next-hop 192.168.32.9		! Niet bestaand ip, dus deze route werkt niet
 !
 

----

 switch2#sh ip route
 Gateway of last resort is 192.168.99.1 to network 0.0.0.0
 
      192.168.99.0/24 is variably subnetted, 4 subnets, 2 masks
 C       192.168.99.11/32 is directly connected, Loopback1
 C       192.168.99.10/32 is directly connected, Loopback0
 C       192.168.99.12/32 is directly connected, Loopback2
 C       192.168.99.0/30 is directly connected, GigabitEthernet1/0/28
 S*   0.0.0.0/0 [1/0] via 192.168.99.1

 switch2#sh ip int brief
 Interface              IP-Address      OK? Method Status                Protocol
 GigabitEthernet1/0/28  192.168.99.2    YES manual up                    up      
 Loopback0              192.168.99.10   YES manual up                    up      
 Loopback1              192.168.99.11   YES manual up                    up      
 Loopback2              192.168.99.12   YES manual up                    up     

 switch2#sh run int gi1/0/28
 interface GigabitEthernet1/0/28
  no switchport
  ip address 192.168.99.2 255.255.255.252
 end

 switch2#sh run int lo0     
 interface Loopback0
  ip address 192.168.99.10 255.255.255.255
 end

 switch2#sh run int lo1
 interface Loopback1
  ip address 192.168.99.11 255.255.255.255
 end

 switch2#sh run int lo2
 interface Loopback2
  ip address 192.168.99.12 255.255.255.255
 end

 switch2#ping 1.1.1.1 source lo0    
 
 Type escape sequence to abort.
 Sending 5, 100-byte ICMP Echos to 1.1.1.1, timeout is 2 seconds:
 Packet sent with a source address of 192.168.99.10 
 !!!!!
 Success rate is 100 percent (5/5), round-trip min/avg/max = 1/4/9 ms

 switch2#ping 1.1.1.1 source lo1
 
 Type escape sequence to abort.
 Sending 5, 100-byte ICMP Echos to 1.1.1.1, timeout is 2 seconds:
 Packet sent with a source address of 192.168.99.11 
 .....
 Success rate is 0 percent (0/5)

 switch2#ping 1.1.1.1 source lo2
 
 Type escape sequence to abort.
 Sending 5, 100-byte ICMP Echos to 1.1.1.1, timeout is 2 seconds:
 Packet sent with a source address of 192.168.99.12 
 !!!!!
 Success rate is 100 percent (5/5), round-trip min/avg/max = 1/2/9 ms

[[Category:Cisco Voorbeeldconfigs]][[Category:Cisco]][[Category:Netwerk]]